The Diablo 500 for the 50th Anniversary Celebration

These posts document restoration experiences of our members
User avatar
Go Go Diablo
Site Admin
Posts:1831
Joined:Fri Feb 22, 2008 12:47 am
Location:Sobieski, Wisconsin
Contact:
Re: The Diablo 500 for the 50th Anniversary Celebration

Post by Go Go Diablo » Wed Nov 02, 2016 10:12 pm

I assemble the hoods complete with decals and then put a protective coating of clear coat on the hood and chassis.
DSC04811.JPG
DSC04811.JPG (164.02KiB)Viewed 9551 times
DSC04839.JPG
DSC04839.JPG (161.83KiB)Viewed 9551 times
Too many Diablos and parts to count.
Yamaha 600 SX

User avatar
Go Go Diablo
Site Admin
Posts:1831
Joined:Fri Feb 22, 2008 12:47 am
Location:Sobieski, Wisconsin
Contact:

Re: The Diablo 500 for the 50th Anniversary Celebration

Post by Go Go Diablo » Wed Nov 02, 2016 10:18 pm

I powder coat my own parts by using a Powder Coater from Harbor Freight. I set the powder coating in an electric oven down at the shop (not the same one my wife makes cookies in!)

Before baking:
DSC04843.JPG
DSC04843.JPG (162.25KiB)Viewed 9551 times
After baking:
DSC04844.JPG
DSC04844.JPG (163.55KiB)Viewed 9551 times
I powder coat all my smaller black parts like bogie stations, bumper brackets, motor mounts and so on. It takes no more time to powder coat as it does to prime and paint, but it is a bit messy.
DSC04847.JPG
DSC04847.JPG (150.2KiB)Viewed 9551 times
DSC04849.JPG
DSC04849.JPG (152.78KiB)Viewed 9551 times
Too many Diablos and parts to count.
Yamaha 600 SX

User avatar
Go Go Diablo
Site Admin
Posts:1831
Joined:Fri Feb 22, 2008 12:47 am
Location:Sobieski, Wisconsin
Contact:

Re: The Diablo 500 for the 50th Anniversary Celebration

Post by Go Go Diablo » Sun Nov 06, 2016 9:51 am

The gearbox for the 500 is different than the 502/503 gearbox. This was Bolens first design for this gearbox and lord knows they had room for improvement.

The first gearboxes had a nylon wheel for the idler sprocket. This nylon wheel wore down so quickly, they must have had gearboxes failing as fast as they could put them together.
DSC04834.JPG
DSC04834.JPG (165.13KiB)Viewed 9538 times
Later 500 gearboxes had a steel sprocket for the idler and the flat bar back plate was lengthened so the oil did not run out of the open gap left by the shorter back plate. These gearboxes also had a very thin grove on the ends of the shaft and a light snap ring was used to hold on the sprockets. I widen out that snap ring groove and install a large heavy E Clip like used on the 502 & 503.
DSC04833.JPG
DSC04833.JPG (164.7KiB)Viewed 9538 times
These gearboxes had one fill hole and that was the hole on the side of the gearcase. I added a fill hole on top of the gearbox and also installed a drain plug in the bottom.
DSC04837.JPG
DSC04837.JPG (163.71KiB)Viewed 9538 times
The gearbox gets a brand new pair of reproduced drive sprocket that will last a lifetime.
DSC04838.JPG
DSC04838.JPG (160.82KiB)Viewed 9538 times
Too many Diablos and parts to count.
Yamaha 600 SX

User avatar
Go Go Diablo
Site Admin
Posts:1831
Joined:Fri Feb 22, 2008 12:47 am
Location:Sobieski, Wisconsin
Contact:

Re: The Diablo 500 for the 50th Anniversary Celebration

Post by Go Go Diablo » Sun Nov 27, 2016 9:26 pm

The motor in the Diablo manual start 500 and 502 is a Hirth 54R. This is a 300cc 16 HP motor. You will see that most of them are red, but in the early 500 production, the motors were a standard Hirth blue. My interpretation of this is the original motors came to Bolens from Hirth the typical blue, but at some point Bolens purchased a bulk order of these motors and had them painted red at the Hirth factory. The red motors are not blue motors painted red, so they were put together red.

Blue or Red, they are exactly the same motor.

The muffler on the Diablo 500 is mounted directly to the motor cylinder. This gives the 500 a really neat sounding BRAAAAPPPP sound different from the other Diablos.

This motor has been rebuild and is ready to install.
DSC02638.JPG
DSC02638.JPG (138.69KiB)Viewed 9502 times
Too many Diablos and parts to count.
Yamaha 600 SX

User avatar
Go Go Diablo
Site Admin
Posts:1831
Joined:Fri Feb 22, 2008 12:47 am
Location:Sobieski, Wisconsin
Contact:

Re: The Diablo 500 for the 50th Anniversary Celebration

Post by Go Go Diablo » Sun Dec 18, 2016 10:14 pm

While I am finishing up a different restoration in the shop, now was a good time to prepare the skis for this Diablo as well.

I use Barrie's Diablo Skis. No one can argue against them being the best reproduction ski available. They are made to the exact detail of the original skis. However, I do add the UHMW wear skins to the bottom of his skis. Once this wear skin is installed, the skis never wear out again. The skins also help hold skis together as without them, even the best skis can crack over time.
DSC05002.JPG
DSC05002.JPG (169.21KiB)Viewed 9215 times
I then install new half oval runners which are what the original skis had.
DSC05005.JPG
DSC05005.JPG (165.23KiB)Viewed 9215 times
I use solid rivets to hold the runners on which makes for a nice connector on top of the ski that you are not catching your boots on.
DSC05004.JPG
DSC05004.JPG (164.76KiB)Viewed 9215 times
Lastly, I stain the skis a solid flat black.
DSC05009.JPG
DSC05009.JPG (185.44KiB)Viewed 9215 times
Too many Diablos and parts to count.
Yamaha 600 SX

User avatar
Go Go Diablo
Site Admin
Posts:1831
Joined:Fri Feb 22, 2008 12:47 am
Location:Sobieski, Wisconsin
Contact:

Re: The Diablo 500 for the 50th Anniversary Celebration

Post by Go Go Diablo » Mon Dec 26, 2016 8:42 pm

To start the assembly of the unit, I always start with the bogie station installations. These original stations have the star clips on the wheels which are pretty much just for show. The wheels are pressed on to the shaft, so they rarely ever come off. All tires and bumpers are like new originals. I do install a lubrication zerk and extra welds on the stations because it would be foolish to assemble any Diablo without doing so.

The original bogie station pins would have been held on with the same star clip as mentioned above. Reusing this design is not advised as they tend to pop off and then the pin can come out. I drill holes in the pins like what has been done on the 502/503 and use a cotter pin.
DSC05034.JPG
DSC05034.JPG (154.59KiB)Viewed 8947 times
DSC05035.JPG
DSC05035.JPG (165.35KiB)Viewed 8947 times
The idler sprockets are new as are the idler sprocket bearings. As you can see, the spring assemblies are held in place with a pair of U-Bolts. A little different design than the 502/503, but effective.
DSC05036.JPG
DSC05036.JPG (150.65KiB)Viewed 8947 times
Too many Diablos and parts to count.
Yamaha 600 SX

User avatar
Go Go Diablo
Site Admin
Posts:1831
Joined:Fri Feb 22, 2008 12:47 am
Location:Sobieski, Wisconsin
Contact:

Re: The Diablo 500 for the 50th Anniversary Celebration

Post by Go Go Diablo » Mon Dec 26, 2016 8:47 pm

After sliding the gearbox in place along with the other front end components, the tracks are ready to install. These are NOS (New Old Stock) tracks which are fitting for this almost new Diablo.
DSC05039.JPG
DSC05039.JPG (163.07KiB)Viewed 8945 times
DSC05038.JPG
DSC05038.JPG (164.25KiB)Viewed 8945 times
Once installed, it is time to flip the Diablo over. As you can see, I've assembled this as the very first Diablos would have been put together.
DSC05040.JPG
DSC05040.JPG (148.81KiB)Viewed 8945 times
It has the long nose tine and only two bumper brackets. It has a fresh chromed bumper on it as well along with chrome bumper bolts.
DSC05041.JPG
DSC05041.JPG (164.95KiB)Viewed 8945 times
Too many Diablos and parts to count.
Yamaha 600 SX

User avatar
Go Go Diablo
Site Admin
Posts:1831
Joined:Fri Feb 22, 2008 12:47 am
Location:Sobieski, Wisconsin
Contact:

Re: The Diablo 500 for the 50th Anniversary Celebration

Post by Go Go Diablo » Mon Dec 26, 2016 8:49 pm

This Diablo also gets a NOS Secondary Clutch. It even has the Bolens Part Number Stickers on it.
DSC05042.JPG
DSC05042.JPG (165.25KiB)Viewed 8945 times
The fuel tank is a refurbished and lined fuel tank. The gas cap is a NOS original cap. Not the best to grab and turn when cold, but this is what the original Diablos had on them.
DSC05043.JPG
DSC05043.JPG (154.51KiB)Viewed 8945 times
Too many Diablos and parts to count.
Yamaha 600 SX

User avatar
Go Go Diablo
Site Admin
Posts:1831
Joined:Fri Feb 22, 2008 12:47 am
Location:Sobieski, Wisconsin
Contact:

Re: The Diablo 500 for the 50th Anniversary Celebration

Post by Go Go Diablo » Tue Dec 27, 2016 10:14 pm

The handle bars on the early 500's were very weak. They later had gussets installed. This new pair of handlebars already had the gussets installed. Although this Diablo is a mock up of an early model 500, it does not pay to put on handlebars without gussets as they would just get bent. So you will need to excuse some details such as this.

The dash on the 500's were very thin and cracked very easily. I was lucky to keep one good original 500 dash around for this special 500.
DSC05046.JPG
DSC05046.JPG (164.73KiB)Viewed 8871 times
DSC05050.JPG
DSC05050.JPG (153.18KiB)Viewed 8871 times
The top end of the dash is held in place with a plate to two brackets that get put over the top openings in the dash. These are only temporary as you will see later.
DSC05049.JPG
DSC05049.JPG (160.41KiB)Viewed 8871 times
Too many Diablos and parts to count.
Yamaha 600 SX

User avatar
Go Go Diablo
Site Admin
Posts:1831
Joined:Fri Feb 22, 2008 12:47 am
Location:Sobieski, Wisconsin
Contact:

Re: The Diablo 500 for the 50th Anniversary Celebration

Post by Go Go Diablo » Tue Dec 27, 2016 10:19 pm

The motor on the early 500's where barely held in place. All the weight of the motor is hanging on the top end motor mounts and soon after driving them around, these usually broke and sent the top of the motor crashing in to the gas tank. For now, we will leave this as original but can add the upgraded motor top bracket later if desired.
DSC05045.JPG
DSC05045.JPG (164.04KiB)Viewed 8871 times
Another really cool thing about a 500 is the muffler is mounted directly to the motor and is under the hood. Although this makes for a hot engine compartment, it makes for a really BRAAAAPY sounding Diablo which I think is pretty cool.
DSC05048.JPG
DSC05048.JPG (155.97KiB)Viewed 8871 times
Too many Diablos and parts to count.
Yamaha 600 SX

Post Reply