400 restoration project

These posts document restoration experiences of our members
User avatar
Barrie2777
Posts:1547
Joined:Tue Mar 04, 2008 9:17 pm
Location:Arundel Quebec
Re: 400 restoration project

Post by Barrie2777 » Wed Sep 21, 2016 5:13 pm

Here are what are probably the last photos for this thread. It has been a battle at times but the end product is as original as it was in 1963-4. I hope you all have enjoyed the ride as well as I have.
Attachments
restored 400 sept 2016.JPG
restored 400 sept 2016.JPG (33.58KiB)Viewed 9872 times
400 engine brake side.JPG
400 engine brake side.JPG (34.96KiB)Viewed 9872 times
400 engine clutch side.JPG
400 engine clutch side.JPG (34.24KiB)Viewed 9872 times

User avatar
fap67
Posts:223
Joined:Tue Oct 06, 2009 5:02 pm

Re: 400 restoration project

Post by fap67 » Wed Sep 21, 2016 7:36 pm

Nice job Barrie, I've been watching this thread from the start, along with all of the other threads too. I've enjoyed them all.

husskifan
Posts:98
Joined:Mon Jan 12, 2009 12:12 pm

Re: 400 restoration project

Post by husskifan » Wed Sep 21, 2016 8:00 pm

NICE JOB BARRIE:

ALWAYS FELT AS THOUGH MY BROTHER AND I WERE THE ONLY ONES WHO KNEW WHAT A HUS-SKI WAS UNTIL THIS CLUB AND YOU CAME ALONG THANK'S BARRIE AND BRUCE.

User avatar
Go Go Diablo
Site Admin
Posts:1831
Joined:Fri Feb 22, 2008 12:47 am
Location:Sobieski, Wisconsin
Contact:

Re: 400 restoration project

Post by Go Go Diablo » Wed Sep 21, 2016 10:24 pm

You are a true craftsman my friend. I am always astonished at what you offer to this forum and this thread is a testament to your knowledge.

For those considering attending the Diablo Rouge 50th Anniversary Celebration on January 14, 2017, Barrie will be there with this 400 and will be speaking at the banquet along with others. Contact me for details.

Bruce
Too many Diablos and parts to count.
Yamaha 600 SX

User avatar
Barrie2777
Posts:1547
Joined:Tue Mar 04, 2008 9:17 pm
Location:Arundel Quebec

Re: 400 restoration project

Post by Barrie2777 » Fri Sep 23, 2016 6:22 am

Yikes!! With that sort of announcement there may be some cancellations for the banquet.

This restoration was also done with the aid of this site. When it was suggested to see a complete JLO rebuild, I knew I could take it apart but the back together correctly part was going to be done with contacts from this site. There are many guys out there who know more about these machines than me. My main go to guys were snowcat Pete, Ken M. and Luc. To them I thank them very much.

User avatar
Jano
Posts:105
Joined:Fri Dec 19, 2008 10:43 am
Location:Gatineau, Qc

Re: 400 restoration project

Post by Jano » Tue Sep 27, 2016 8:13 am

Excellent job Barrie. Can't wait to see it in the Port. Can I expect you to bring along a red one too? After all, it is a Diablo reunion and maybe it's time for us to see you ride a Diablo. Get your cameras ready folks, just in case.

BillNH
Posts:100
Joined:Tue May 12, 2009 6:54 pm
Location:Charlestown, NH

Re: 400 restoration project

Post by BillNH » Thu Oct 13, 2016 1:47 pm

I was trying to understand how to set the flywheel timing. Then I got to looking at the flywheel in the L252L that I have, and both key slots are marked with an arrow for rotation. The arrow would be covered by the washer when installed, and is about 10mm or 3/8 inch from each slot. The cam also has arrows in each slot. This should make my job easier.
Bill, 503 Diablo Rouge, 444 mongrel. 2009 Arctic Cat 570

User avatar
Barrie2777
Posts:1547
Joined:Tue Mar 04, 2008 9:17 pm
Location:Arundel Quebec

Re: 400 restoration project

Post by Barrie2777 » Sat Dec 31, 2016 12:59 pm

My 400 has had a serious set back for its readiness for Port Washington. It had begun to have starting issues and increased revs. My fear of a leaking seal has to be confirmed when the revs went to 5000. As muphy' s law goes, the pto seal seemed good so I pulled all the parts on the mag side to discover an oil leak at the bearing seal. This seal is the problem.

User avatar
Barrie2777
Posts:1547
Joined:Tue Mar 04, 2008 9:17 pm
Location:Arundel Quebec

Re: 400 restoration project

Post by Barrie2777 » Mon Jan 02, 2017 10:45 pm

Here was the blown gasket that ended up being the problem! There must have been an air leak at this spot but it wasn't known until the gasket blew out.
Attachments
IRS20170103_074217.jpg
IRS20170103_074217.jpg (28.96KiB)Viewed 9351 times

User avatar
randys444
Posts:95
Joined:Fri Apr 22, 2016 6:43 pm

Re: 400 restoration project

Post by randys444 » Tue Feb 07, 2017 9:55 pm

Beautiful job on this restoration. There is so much information here. Been learning about these recoils as mine is backwards. Also these JLOs with there L and R rotation. Looks like I have a job ahead of me. Your details on these machines are amazing.
Bring on the snow

Post Reply