model 600 restoration

These posts document restoration experiences of our members
Post Reply
User avatar
Barrie2777
Posts:1547
Joined:Tue Mar 04, 2008 9:17 pm
Location:Arundel Quebec
model 600 restoration

Post by Barrie2777 » Mon Nov 14, 2011 6:57 am

Here is the begining of the restoration of a model 600 single track and 600 double track.
Attachments
DSC03499.JPG
exhaust port
DSC03499.JPG (554.3KiB)Viewed 17683 times
DSC03498.JPG
two seater pins were installed.
DSC03498.JPG (609.34KiB)Viewed 17683 times
600 double track.jpg
the before photo of the double track
600 double track.jpg (144.34KiB)Viewed 17683 times

User avatar
huuksnatch
Posts:75
Joined:Fri Aug 01, 2008 1:19 pm
Location:Calumet MI

Re: model 600 restoration

Post by huuksnatch » Mon Nov 14, 2011 9:23 am

Those 2 seater pins factory i take it?
-Steve

User avatar
Barrie2777
Posts:1547
Joined:Tue Mar 04, 2008 9:17 pm
Location:Arundel Quebec

Re: model 600 restoration

Post by Barrie2777 » Mon Nov 14, 2011 3:22 pm

The double seater pins appear to be factory installed.

User avatar
Barrie2777
Posts:1547
Joined:Tue Mar 04, 2008 9:17 pm
Location:Arundel Quebec

Re: model 600 restoration

Post by Barrie2777 » Wed Nov 16, 2011 8:54 pm

The sprocket on the 600 single track is much smaller than any other HUS-SKI.
Attachments
600 base 2.jpg
drive axel for the single track 600
600 base 2.jpg (143.58KiB)Viewed 17641 times

User avatar
Barrie2777
Posts:1547
Joined:Tue Mar 04, 2008 9:17 pm
Location:Arundel Quebec

Re: model 600 restoration

Post by Barrie2777 » Sun Dec 04, 2011 5:36 pm

The single track 600 base that I am starting with is actually an NOS unit. However, the last 40 years outside in the weeds has taken it toll. The reinforcing strip just behind the seater pin was rusted through and the rear deck support was a pitted and rusted through disaster. Luckily, in the "why do I keep this category" I had a basket case, double track base which had both parts in very good condition. Cutting them from the original base was not difficult but removing the parts I was replacing was more difficult, having to be careful not to damage the surrounding metal.
Attachments
salvaged parts from parts base.jpg
salvaged parts from parts base.jpg (132.43KiB)Viewed 17561 times
rusted area removed.jpg
rusted area removed.jpg (146.11KiB)Viewed 17561 times
salvaged part in place.jpg
salvaged part in place.jpg (147.31KiB)Viewed 17561 times

User avatar
Barrie2777
Posts:1547
Joined:Tue Mar 04, 2008 9:17 pm
Location:Arundel Quebec

Re: model 600 restoration

Post by Barrie2777 » Sun Dec 04, 2011 6:09 pm

This is the rusted rear deck brace
Attachments
rusted through rear deck brace.jpg
rusted through rear deck brace.jpg (143.47KiB)Viewed 17559 times

User avatar
Barrie2777
Posts:1547
Joined:Tue Mar 04, 2008 9:17 pm
Location:Arundel Quebec

Re: model 600 restoration

Post by Barrie2777 » Sun Jan 01, 2012 9:33 am

The curved portion on the front of the base was rusted through on this base so I cut it off and formed a new part.
Attachments
replacing front of single track base 003.jpg
replacing front of single track base 003.jpg (148.37KiB)Viewed 17467 times
replacing front of single track base 002.jpg
replacing front of single track base 002.jpg (135.78KiB)Viewed 17467 times

User avatar
Barrie2777
Posts:1547
Joined:Tue Mar 04, 2008 9:17 pm
Location:Arundel Quebec

Re: model 600 restoration

Post by Barrie2777 » Sun Jan 01, 2012 3:05 pm

This parts was welded continuously along the ends , spot welded along the bottom edge and welded in various places along the top edge. To duplicate the spot welding, I first drill a small hole then weld in the hole.
Attachments
front of single track base welded in place.jpg
front of single track base welded in place.jpg (144.52KiB)Viewed 17454 times

User avatar
Barrie2777
Posts:1547
Joined:Tue Mar 04, 2008 9:17 pm
Location:Arundel Quebec

Re: model 600 restoration

Post by Barrie2777 » Sun Jan 01, 2012 5:32 pm

Odd as it may be, all the dash panels were badly pitted or otherwise cut and/or altered. I cut the handlebars behind the dash panel to hide any welding done to reattach the handlebars. What seemed like a simple task turned out to be difficult due to the amount of original welding done to hold the dash panel in place. It is no wonder these 600's were "tanks". The dash and body was made with what I estimate to be 16 ga steel. I did not want to work with this thickness so did it slightly lighter with 18 ga. The dash is essentially a large "U" and certainly strong on its own but HUS-SKI engineers welded in two full support gussets to weld it even more securely to the handlebars. In the photo in the next posting you can see that the dash was not the weak part of this assembly.
Attachments
600 dash removal.jpg
600 dash removal.jpg (133.44KiB)Viewed 17448 times
reproduced 600 dash 001.jpg
reproduced 600 dash 001.jpg (130.95KiB)Viewed 17448 times

User avatar
Barrie2777
Posts:1547
Joined:Tue Mar 04, 2008 9:17 pm
Location:Arundel Quebec

Re: model 600 restoration

Post by Barrie2777 » Sun Jan 01, 2012 5:36 pm

Doing three at a time is always a time saver. The hole for the handlebars is oval because the dash is at an angle to the handlebar tubing. To reassemble the dash, the dash will be slid onto the front portion of the handlebars, then the handlebars will be welded back to their correct position. Then the dash is slid back to where it should be (hopefully covering all the welding) and welded in place.
Attachments
3 reproduced 600 dashes.jpg
3 reproduced 600 dashes.jpg (131.7KiB)Viewed 17448 times
600 altered handlebars.jpg
600 altered handlebars.jpg (158.72KiB)Viewed 17448 times

Post Reply