200

These posts document restoration experiences of our members
User avatar
snocatpete
Posts:376
Joined:Sun Feb 07, 2010 8:39 pm
Re: 200

Post by snocatpete » Wed Mar 04, 2020 11:49 pm

After shaping the stainless steel covers and varnishing the wood skid, I assembled the two pieces together and they are now ready to be installed at a later date.
Attachments
IMG_8536.jpg
IMG_8536.jpg (39.95KiB)Viewed 4794 times
IMG_8541.jpg
IMG_8541.jpg (43.89KiB)Viewed 4794 times
IMG_8542.jpg
IMG_8542.jpg (42.61KiB)Viewed 4794 times

User avatar
snocatpete
Posts:376
Joined:Sun Feb 07, 2010 8:39 pm

Re: 200

Post by snocatpete » Sat May 09, 2020 11:27 am

Back in an earlier posting I said a new drive chain would be required. Fortunately since then I was able to acquire a NOS replacement drive chain hus ski part # 180-1689. And now I am debating if I should use it or just use a new high-quality diamond brand replacement chain. Because if I do use it, it will wear and wear out and eventually need to be replaced, then it’s gone forever or do I save it and use it as a display piece ? This is the ONLY time I’ve ever seen a hus ski NOS drive chain. But I guess I could ask the same question about the NOS skis i have for this restoration ...use them or save them??


I guess I will decide that when it’s time for final assembly ??
Attachments
IMG_9648.jpg
IMG_9648.jpg (26.59KiB)Viewed 4727 times
IMG_9650.jpg
IMG_9650.jpg (24.85KiB)Viewed 4727 times

User avatar
snocatpete
Posts:376
Joined:Sun Feb 07, 2010 8:39 pm

Re: 200

Post by snocatpete » Sat May 09, 2020 11:30 am

This is a comparison between the original and the NOS
Attachments
IMG_9635.jpg
IMG_9635.jpg (37.66KiB)Viewed 4727 times
IMG_9638.jpg
IMG_9638.jpg (34.55KiB)Viewed 4727 times
IMG_9639.jpg
IMG_9639.jpg (43.32KiB)Viewed 4727 times

User avatar
snocatpete
Posts:376
Joined:Sun Feb 07, 2010 8:39 pm

Re: 200

Post by snocatpete » Tue May 19, 2020 6:07 pm

The original tracks were completely worn out and there was no question that new ones would need to be built. Fortunately none of the steel channel cleats were missing as these would need to be removed and reused on the new ones. After the steel channel cleats were removed I gave them a thorough cleaning to get them down to bare metal and then a couple of coats of black paint . Next I had to cut, drill and varnish all the wood cleats, then pre-drill all the new rubber belting. Then it was time to start assembling the tracks. I use rivets and washers like the originals.

One thing I did differently from the original tracks is I used alligator type lacer clips rather than the original clipper type lacers. I did this for two reasons: 1 - I think they are a stronger design and 2 - I have the tools to install the alligator lacers.

It doesn’t matter what method you use, building or rebuilding Hus-ski tracks is a lot of work!
Attachments
IMG_8659.jpg
IMG_8659.jpg (40.53KiB)Viewed 4680 times
IMG_8657.jpg
IMG_8657.jpg (39.12KiB)Viewed 4680 times
IMG_8656.jpg
IMG_8656.jpg (39.31KiB)Viewed 4680 times

User avatar
snocatpete
Posts:376
Joined:Sun Feb 07, 2010 8:39 pm

Re: 200

Post by snocatpete » Tue May 19, 2020 6:08 pm

removing and painting ice cleats
Attachments
IMG_9529.jpg
IMG_9529.jpg (40.37KiB)Viewed 4680 times
IMG_9533.jpg
IMG_9533.jpg (40KiB)Viewed 4680 times
IMG_9538.jpg
IMG_9538.jpg (31.53KiB)Viewed 4680 times

User avatar
snocatpete
Posts:376
Joined:Sun Feb 07, 2010 8:39 pm

Re: 200

Post by snocatpete » Tue May 19, 2020 6:10 pm

Assembling tracks
Attachments
IMG_9547.jpg
IMG_9547.jpg (37.92KiB)Viewed 4680 times
IMG_9550.jpg
IMG_9550.jpg (43.43KiB)Viewed 4680 times
IMG_9552.jpg
IMG_9552.jpg (39.1KiB)Viewed 4680 times

User avatar
snocatpete
Posts:376
Joined:Sun Feb 07, 2010 8:39 pm

Re: 200

Post by snocatpete » Tue May 19, 2020 6:11 pm

Installing lacer clips and brand new tracks
Attachments
IMG_9560.jpg
IMG_9560.jpg (46.58KiB)Viewed 4680 times
IMG_9561.jpg
IMG_9561.jpg (42.57KiB)Viewed 4680 times
IMG_9562.jpg
IMG_9562.jpg (40.38KiB)Viewed 4680 times

User avatar
myoldhus-ski
Posts:82
Joined:Thu Jan 21, 2010 10:01 pm
Location:Poplar Point Manitoba

Re: 200

Post by myoldhus-ski » Tue May 19, 2020 10:01 pm

Aren't tracks fun!! I have a spare set built for my 600 and I hope I never need them. Jim

User avatar
snocatpete
Posts:376
Joined:Sun Feb 07, 2010 8:39 pm

Re: 200

Post by snocatpete » Fri May 29, 2020 10:47 pm

After test fitting all the sheet metal parts together and making sure they fit nicely it was time to take it apart and take it to the media blasting and then get it prepped for paint.
In order to move this restoration forward I had to out source the media blasting to remove all the old paint and any surface rust. Normally I do this myself but the local DIY place I go to is closed due to the pandemic.
Now that it’s back from media blasting I have to refit the parts to make sure everything still fits nicely. Then it’s on to prepping the bare metal for priming and then eventually the final paint.
Attachments
IMG_0172.jpg
IMG_0172.jpg (22.02KiB)Viewed 4480 times
IMG_0170.jpg
IMG_0170.jpg (28.1KiB)Viewed 4480 times

User avatar
snocatpete
Posts:376
Joined:Sun Feb 07, 2010 8:39 pm

Re: 200

Post by snocatpete » Mon Jun 01, 2020 11:24 pm

Today I picked up the primer and paint. Both the paint and the primer I use is a three-part single stage automotive type paint.
It requires a spray gun and compressed air to apply the primer and paint so my next step now is to get all the parts into the paint booth and start painting. Wow, automotive paint is expensive!! But this type of paint will have a hard, shiny, durable finish that will last another 50 years.
Attachments
IMG_0178.jpg
IMG_0178.jpg (31.09KiB)Viewed 4411 times

Post Reply