motor dismantling
- Barrie2777
- Posts:1547
- Joined:Tue Mar 04, 2008 9:17 pm
- Location:Arundel Quebec
I hope this won't be a big problem, but the motor on the Diablo I just Got (yes another one!) rain entered the cylinder during all our rain last week. The carb was off and the heatshield did a great funnelling job. I have taken the motor inside, heated it up to thaw the ice inside and poured out the water. I have removed the clyinder and managed to separate the crankcase about 1/8". I sprayed all bearings and inner parts with WD40. To go further I will need to pull the flywheel. Should I completely dismantle the engine or is this drying out method enough to ensure no rusting on bearings and wrist pin rollers?
-
- Posts:165
- Joined:Sun Feb 24, 2008 9:14 am
- Location:World Famous Horicon Marsh
- Contact:
Re: motor dismantling
I've heard of people that have sunk there entire snowmobile, then thaw it out, put new gas in it & run it. My opinion you have taken it farther than most would even consider! Heck if you're that far why not just take it apart, check & clean it up then reassemble. That way you know what you have when you're done. Just my 2 cents
BOTTOMS UP!
BOTTOMS UP!
69 Diablo "503"
72 Kitty cat
74 JD 295s (1 1/2X)
7? Jdx8
81 Spitfire
80 Liquifire CUSTOM
94 Indy
94 XCR 440
72 Kitty cat
74 JD 295s (1 1/2X)
7? Jdx8
81 Spitfire
80 Liquifire CUSTOM
94 Indy
94 XCR 440
Re: motor dismantling
Hi Barrie,
I would aggree with Dave. I know of guys like Dave mentioned and they did as stated. Heck we sunk a couple of quads, pulled the plugs turned them over to get the water out, got them fired up and contiued on with no issues. I Have also heard of guys who have sunk sleds, after draining the water, ran Mercury Marine Storage Seal to ensure no rusting.
Ken
I would aggree with Dave. I know of guys like Dave mentioned and they did as stated. Heck we sunk a couple of quads, pulled the plugs turned them over to get the water out, got them fired up and contiued on with no issues. I Have also heard of guys who have sunk sleds, after draining the water, ran Mercury Marine Storage Seal to ensure no rusting.
Ken
- Barrie2777
- Posts:1547
- Joined:Tue Mar 04, 2008 9:17 pm
- Location:Arundel Quebec
Re: motor dismantling
The motor is now completely dismantled. Good thing too..I found a rusted and pitted bearing not due to the last rain but from a day long past. The number 6305 is on the bearing . I assume this is still a valid number? I will probably relace the other bearing since I have come this far but it appears to be in excellent condition. The spark plug wire is also suspect.
- Go Go Diablo
- Site Admin
- Posts:1830
- Joined:Fri Feb 22, 2008 12:47 am
- Location:Sobieski, Wisconsin
- Contact:
Re: motor dismantling
Barrie,
The bearing number is standard nomenclature for bearing identifications. You will have no problems matching up that bearing. In that you have the motor this far taken apart, I'd suggest getting new condenser and points. Condensers can loose their capacitance over time.
Bruce
The bearing number is standard nomenclature for bearing identifications. You will have no problems matching up that bearing. In that you have the motor this far taken apart, I'd suggest getting new condenser and points. Condensers can loose their capacitance over time.
Bruce
Too many Diablos and parts to count.
Yamaha 600 SX
Yamaha 600 SX
- Barrie2777
- Posts:1547
- Joined:Tue Mar 04, 2008 9:17 pm
- Location:Arundel Quebec
Re: motor dismantling
This engine is getting the rebuild. The piston and rings look great and no scoring in the cylinder. The only problem I see is the bearing which was on the flywheel side. Is it possible that a leaking seal had let water in?