Hus Ski skis for Diablo or Diablo skis for a Hus Ski ?????

A place for all your Diablo Rouge Questions or just a place to shoot the bull about those little Red Devils.

Hus Ski skis for Diablo or Diablo skis for a Hus Ski ?????

Postby Schoobytwo (Bruce) » Tue Jan 05, 2016 10:07 pm

Tonight I am starting to put wear skins on two sets of NOS skis for a friend from the Diablo heartland of the Port Washington area. To install the skins, I need to remove the hardware and sand the paint off the bottom of the ski to expose the bare wood. While I was taking the factory runners off, I noticed the hole pattern for the ski retainer plates is not the same between the pairs. :?:

I've seen this a few other times but thought someone just made a mistake drilling holes. But these skis are evidence that Bolens had something else in mind.

A typical Diablo ski retainer hole pattern is narrow side to side and long end to end. The Diablo ski is on the left and the unknown ski is on the right.

DSC04307.JPG
DSC04307.JPG (149.23 KiB) Viewed 3027 times


So when I've seen this in the past, the skis did not have part numbers on them. However, these skis do. Diablo skis are either part number 180-1164 for the ski or 180-1197 for the ski with the runner sold as an assembly. This unusual pair of skis has an original Bolens part number tag on it and the part number is 180-1872.

DSC04308.JPG
DSC04308.JPG (164.97 KiB) Viewed 3027 times


This hole pattern is about 3-1/2" center to center side to side of ski and about 4=1/8" center to center end to end. Much more squarer than the Diablo ski retainer hole pattern.

DSC04310.JPG
DSC04310.JPG (161.11 KiB) Viewed 3027 times


In addition, the runners I removed were more like a Hus Ski ski. They had 6 rivets holding them on versus the typical 5 that a Diablo ski would have. The runners also did not have the center bolt hole that the Diablo skis have where the single taper headed 1/4" bolt comes up through the runner, the wood and into the center of the ski retainer plate.

That certainly is not a ski drilled from the factory made for the Diablo. Any ideas?????
Too many Diablos and parts to count.
Yamaha Apex (it outruns the Diablo for sure)
Yamaha 600 SX
User avatar
Schoobytwo (Bruce)
Site Admin
 
Posts: 1710
Joined: Fri Feb 22, 2008 12:47 am
Location: Sobieski, Wisconsin

Re: Hus Ski skis for Diablo or Diablo skis for a Hus Ski ???

Postby Barrie2777 » Fri Jan 08, 2016 12:09 pm

That appears to be the hole pattern for HUS-SKI skis. YIKES!! Since Diablo skis are shorter than HUS-SKI skis the location should not be at the center point of the ski and a ski that wide on a HUS-SKI would probably come into contact with the tool box because HUS-SKI skis are hinged.
User avatar
Barrie2777
 
Posts: 1432
Joined: Tue Mar 04, 2008 9:17 pm
Location: Arundel Quebec

Re: Hus Ski skis for Diablo or Diablo skis for a Hus Ski ???

Postby Schoobytwo (Bruce) » Mon Jan 11, 2016 10:27 pm

Confirmed by the Hus Ski expert! :-0

Just when I think I've seen it all, something like this pops up. Someday we might run across the documents that fills in the blanks of the things we think we know and then the Bolens method of madness will become clear. :D

Bruce
Too many Diablos and parts to count.
Yamaha Apex (it outruns the Diablo for sure)
Yamaha 600 SX
User avatar
Schoobytwo (Bruce)
Site Admin
 
Posts: 1710
Joined: Fri Feb 22, 2008 12:47 am
Location: Sobieski, Wisconsin


Return to Questions & Discussions about Diablos

Who is online

Users browsing this forum: No registered users and 1 guest