The Diablo 500 for the 50th Anniversary Celebration

These posts document restoration experiences of our members
User avatar
Go Go Diablo
Site Admin
Posts:1830
Joined:Fri Feb 22, 2008 12:47 am
Location:Sobieski, Wisconsin
Contact:
Re: The Diablo 500 for the 50th Anniversary Celebration

Post by Go Go Diablo » Tue Dec 27, 2016 10:21 pm

The original 500's had a chrome plastic nose cone. The chrome was so poorly applied, it just blew off in the wind and left you with a dull white nose cone. These new chrome nose cones are much better. The nose cone is held in place by two NOS headlight assemblies.
DSC05044.JPG
DSC05044.JPG (164.67KiB)Viewed 5021 times
Too many Diablos and parts to count.
Yamaha 600 SX

User avatar
Go Go Diablo
Site Admin
Posts:1830
Joined:Fri Feb 22, 2008 12:47 am
Location:Sobieski, Wisconsin
Contact:

Re: The Diablo 500 for the 50th Anniversary Celebration

Post by Go Go Diablo » Sat Dec 31, 2016 9:57 am

The original handle pins are very shallow on the top and have these wide aluminum press clips under them. I had a pair of the original pins re-chromed along with the half moon handles and had a good pair of original clips.
DSC05053.JPG
DSC05053.JPG (155.13KiB)Viewed 5012 times
The wiring on a 500 or 502 is fairly simple. A new key switch, new light switch and all new wires makes for a clean looking harness.
DSC05063.JPG
DSC05063.JPG (165.07KiB)Viewed 5012 times
Too many Diablos and parts to count.
Yamaha 600 SX

User avatar
Go Go Diablo
Site Admin
Posts:1830
Joined:Fri Feb 22, 2008 12:47 am
Location:Sobieski, Wisconsin
Contact:

Re: The Diablo 500 for the 50th Anniversary Celebration

Post by Go Go Diablo » Sat Dec 31, 2016 10:03 am

The carb I installed is an original Tillotson HR3A that would have been on the 500's. I've started using Tygon fuel line as it is softer and better quality.
DSC05061.JPG
DSC05061.JPG (165.29KiB)Viewed 5012 times
DSC05062.JPG
DSC05062.JPG (165.22KiB)Viewed 5012 times
Too many Diablos and parts to count.
Yamaha 600 SX

User avatar
Go Go Diablo
Site Admin
Posts:1830
Joined:Fri Feb 22, 2008 12:47 am
Location:Sobieski, Wisconsin
Contact:

Re: The Diablo 500 for the 50th Anniversary Celebration

Post by Go Go Diablo » Sat Dec 31, 2016 10:06 am

The original Primary Clutch on the 500 would have the three small allen headed screws holding the ramp plate on, so I installed the same clutch on this unit.
DSC05059.JPG
DSC05059.JPG (165.16KiB)Viewed 5012 times
I also installed an original NOS Saylers belt which would have been common in that time.
DSC05060.JPG
DSC05060.JPG (164.13KiB)Viewed 5012 times
Too many Diablos and parts to count.
Yamaha 600 SX

User avatar
Go Go Diablo
Site Admin
Posts:1830
Joined:Fri Feb 22, 2008 12:47 am
Location:Sobieski, Wisconsin
Contact:

Re: The Diablo 500 for the 50th Anniversary Celebration

Post by Go Go Diablo » Sat Dec 31, 2016 10:17 am

As mentioned early on, I found an original windshield bracket for a 500. For many years, we thought the windshield was just a myth as it was only ever seen in the promo-video for the 500. Since then, I have come across two factory brackets both missing the windshield. Bill S from Stone Lake, WI gave me a picture of his Diablo 500 taken back in 1967 and it had a windshield. Nate over in the thumb of Michigan also had a NOS windshield. So that is four that I know of.

I struggled to get someone to make a windshield for me. I tried working with two different companies looking for someone to reproduce this and although both held the pattern and pieces for months, neither completed the project. So buying a piece of windshield material myself, I made my own.

Cutting out the material based on the pattern, I then connected it to a piece of 2" PVC. Using my heat gun, I softened the material and rolled it over the PVC.
DSC05055.JPG
DSC05055.JPG (164.54KiB)Viewed 5012 times
It was a trick to get the windshield in the frame. And then another trick to put on the trim and hold it there, but in the end, I am very happy with what I came up with. To my knowledge, this may very well be the only Diablo 500 in existence that has a factory windshield on it.
DSC05065.JPG
DSC05065.JPG (164.37KiB)Viewed 5012 times
DSC05064.JPG
DSC05064.JPG (164.91KiB)Viewed 5012 times
The tractor half of this restoration is complete. On to the ski seater!
Too many Diablos and parts to count.
Yamaha 600 SX

User avatar
Go Go Diablo
Site Admin
Posts:1830
Joined:Fri Feb 22, 2008 12:47 am
Location:Sobieski, Wisconsin
Contact:

Re: The Diablo 500 for the 50th Anniversary Celebration

Post by Go Go Diablo » Sat Dec 31, 2016 8:06 pm

The 500 seaters did not have the grab bar around the back. Some of the early seaters also did not have the support inside the toolbox which meant when you got a couple of people on the seater, it tended to cave in. For this restoration, I chose to use a seater that is original and has the updated internal support.
DSC05069.JPG
DSC05069.JPG (164.15KiB)Viewed 5006 times
Of course, a restoration like this can only have Barrie's authentic maple skis on them. I stained them black and added the Durasurf wear skins under them. The runners are new. I rivet the runners on to the skis and then use elevator bolts to attach the skis to the seater spring.
DSC05066.JPG
DSC05066.JPG (150.57KiB)Viewed 5006 times
DSC05067.JPG
DSC05067.JPG (143.93KiB)Viewed 5006 times
Tighten things down, add the wiring and the tail light and we are ready for the seat.
DSC05070.JPG
DSC05070.JPG (164.25KiB)Viewed 5006 times
Too many Diablos and parts to count.
Yamaha 600 SX

User avatar
Go Go Diablo
Site Admin
Posts:1830
Joined:Fri Feb 22, 2008 12:47 am
Location:Sobieski, Wisconsin
Contact:

Re: The Diablo 500 for the 50th Anniversary Celebration

Post by Go Go Diablo » Sat Dec 31, 2016 8:11 pm

I may have told you the story behind this seat, but it is worth repeating.

I lived close to my parents my whole life, so I saw them almost weekly. My father died about 6 years ago and a few years later, my mother passed away. In the process of cleaning out their house that I was born in, I found this original Diablo 500 seat buried in the attic. It was one of the last areas of the house we were cleaning up and to find it was a gift from pops I'm sure. It is my gift to this unique Diablo restoration.
DSC05056.JPG
DSC05056.JPG (172.99KiB)Viewed 5006 times
Too many Diablos and parts to count.
Yamaha 600 SX

User avatar
Go Go Diablo
Site Admin
Posts:1830
Joined:Fri Feb 22, 2008 12:47 am
Location:Sobieski, Wisconsin
Contact:

Re: The Diablo 500 for the 50th Anniversary Celebration

Post by Go Go Diablo » Sat Dec 31, 2016 8:18 pm

Presenting - a restoration of an original 1967 Bolens Diablo Rouge Snowmobile.
DSC05073.JPG
DSC05073.JPG (147.23KiB)Viewed 5006 times
DSC05078.JPG
DSC05078.JPG (157.82KiB)Viewed 5006 times
DSC05077.JPG
DSC05077.JPG (132.08KiB)Viewed 5006 times
DSC05080.JPG
DSC05080.JPG (151.26KiB)Viewed 5006 times
DSC05079.JPG
DSC05079.JPG (165.02KiB)Viewed 5006 times
DSC05082.JPG
DSC05082.JPG (163KiB)Viewed 5006 times
We hope you will all come to the Banquet on Saturday Night to get a look at it, enjoy the presentations, have a great meal and win prizes.

Thank you all for your support through the years.

Bruce
Too many Diablos and parts to count.
Yamaha 600 SX

User avatar
Barrie2777
Posts:1547
Joined:Tue Mar 04, 2008 9:17 pm
Location:Arundel Quebec

Re: The Diablo 500 for the 50th Anniversary Celebration

Post by Barrie2777 » Mon Jan 02, 2017 8:07 am

Great looking machine Bruce. I like the yellow gas line!!

I had heard that the SAYLERS belt was made for a dealer by the name of SAYLERS. Have you heard this?

husskifan
Posts:98
Joined:Mon Jan 12, 2009 12:12 pm

Re: The Diablo 500 for the 50th Anniversary Celebration

Post by husskifan » Mon Jan 02, 2017 9:35 pm

BRUCE GREAT JOB, IT LOOKS LIKE BRAND NEW, AND I AM SURE BETTER THAN NEW.

Post Reply