model 600 restoration

These posts document restoration experiences of our members
User avatar
Barrie2777
Posts:1547
Joined:Tue Mar 04, 2008 9:17 pm
Location:Arundel Quebec
Re: model 600 restoration

Post by Barrie2777 » Sat Jun 01, 2013 7:47 am

With the primary clutch repaired and all other systems a "go" I took this project for it's inaugural ride. The 600 rides and handles like no other HUS-SKI. I even banged my knees once going through a very slight hollow. The handlebars are not bent upwards on the 600 and this makes a big difference in "knee" clearance. The engine would run great for about 5 minutes then want to stall. Although it never stalled,it did require a minute or two to prep itself for the next 5 minutes. I am putting this down to the very warm day I was riding it and hopefully next winter on a cold day this will not happen. The hood on this machine is original and has not been upgraded with the addition of the top side vent.
Attachments
600 maiden voyage 003.jpg
600 maiden voyage 003.jpg (419.81KiB)Viewed 8186 times
600 maiden voyage 001.jpg
600 maiden voyage 001.jpg (434.55KiB)Viewed 8186 times

User avatar
myoldhus-ski
Posts:82
Joined:Thu Jan 21, 2010 10:01 pm
Location:Poplar Point Manitoba

Re: model 600 restoration

Post by myoldhus-ski » Sat Jun 01, 2013 12:44 pm

It looks great Barrie. Those single track 600's certainly look top heavy don't they. Jim

User avatar
Barrie2777
Posts:1547
Joined:Tue Mar 04, 2008 9:17 pm
Location:Arundel Quebec

Re: model 600 restoration

Post by Barrie2777 » Tue Dec 10, 2013 8:40 am

There is nothing more beautiful than a newly rebuilt set of HUS-SKI tracks. The set on the right is for my 600 double track while the other set is rebuilt to put my 400 in top shape again. It was throwing too many cleats last winter due to the cleats being worn through to less than half their thickness. I always advocate riveting the cleats and ice cleats due to original appearance and ease of fastening. Riveting by hand would not be too tempting but I use a riveting end on an air hammer. It take about 15 seconds to rivet the four or five rivets on either of these tracks. To assemble the 600 tracks I insert all the rivets ( and washers) first then push on one wood cleat and its respective ice cleat. Rivet it together and procede until all are done. This process takes just over one hour per track.
Attachments
tracks 231.JPG
riveted as original tracks
tracks 231.JPG (160.03KiB)Viewed 8020 times
tracks 227.JPG
rebuilt tracks
tracks 227.JPG (151.91KiB)Viewed 8020 times

User avatar
Barrie2777
Posts:1547
Joined:Tue Mar 04, 2008 9:17 pm
Location:Arundel Quebec

Re: model 600 restoration

Post by Barrie2777 » Sun Apr 06, 2014 8:37 am

My progress on this 600 double track has been very slow but here is another installment in its progress. The secondary on the 600's is identical in appearance to those of the 200-A but when taken apart you find a plastic sleeve which fits tightly over the post of the fixed sheeve. I see this as a design improvement to reduce wear. This sleeve appears to simply be a piece of ABS plastic water pipe turned to the correct OD. These plastic sleeved secondaries can be found on 200-A's of the same year. Since the jackshaft housing is the same as other HUS-SKIs (excluding the wonderful 600 single track) and the bracket for the housing is the same width as the single track (wider) there is an aluminum spacer and several thick washers required to make up the difference.
Attachments
April 6,2014 097.JPG
parts of secondary clutch
April 6,2014 097.JPG (364.65KiB)Viewed 7916 times
April 6,2014 096.JPG
cleaned secondary
April 6,2014 096.JPG (239.6KiB)Viewed 7916 times

User avatar
Barrie2777
Posts:1547
Joined:Tue Mar 04, 2008 9:17 pm
Location:Arundel Quebec

Re: model 600 restoration

Post by Barrie2777 » Sun Feb 05, 2017 12:19 pm

Finally after so many years of having done the restoration of this single track, I installed the chrome bumper. I made the bumper then sent it for chroming.the double track machine beside it has the black bumper.
Attachments
20170205_121542.jpg
600 chrome bumper
20170205_121542.jpg (975.94KiB)Viewed 6282 times

User avatar
Barrie2777
Posts:1547
Joined:Tue Mar 04, 2008 9:17 pm
Location:Arundel Quebec

Re: model 600 restoration

Post by Barrie2777 » Sat Jan 27, 2018 9:51 pm

Here i go again on a 600. This one was painted and asembled several years ago. The engine was never installed.
Attachments
600doubletrack252.jpg
600doubletrack252.jpg (157.27KiB)Viewed 6014 times

User avatar
Jano
Posts:105
Joined:Fri Dec 19, 2008 10:43 am
Location:Gatineau, Qc

Re: model 600 restoration

Post by Jano » Tue Jan 30, 2018 12:34 pm

Is this going to be a L292 engine?

User avatar
Barrie2777
Posts:1547
Joined:Tue Mar 04, 2008 9:17 pm
Location:Arundel Quebec

Re: model 600 restoration

Post by Barrie2777 » Tue Jan 30, 2018 3:07 pm

Jano you are giving away secrets.

User avatar
Barrie2777
Posts:1547
Joined:Tue Mar 04, 2008 9:17 pm
Location:Arundel Quebec

Re: model 600 restoration

Post by Barrie2777 » Wed Jan 31, 2018 8:35 pm

Now that the cat is out of the bag..yss my plan was to put a jlo 292 in this machine however i dont have the time to convert the 292 i have into a right hand rotation. Instead i plan to install the carbs shown in the photo.
Attachments
doublecarb.jpg
doublecarb.jpg (284.94KiB)Viewed 5986 times

User avatar
Barrie2777
Posts:1547
Joined:Tue Mar 04, 2008 9:17 pm
Location:Arundel Quebec

Re: model 600 restoration

Post by Barrie2777 » Sun Feb 04, 2018 5:16 pm

Although these carbs were made for the 252 JLO they were for another machine. This means that the throttle linkage and choke linkage is all backwards for a HUSSKI. The "y" for the carb has the impulse hole on the bottom carb. Flipping the carbs was okey because both carbs had an impulse carb. The main carb is on the bottom now. Via a tube to the slave carb, the vacuum will be transferred.
Attachments
carbsflipped.jpg
carbsflipped.jpg (171.19KiB)Viewed 5973 times

Post Reply