model 600 restoration
- Barrie2777
- Posts:1547
- Joined:Tue Mar 04, 2008 9:17 pm
- Location:Arundel Quebec
These carbs were originally set to have a "vertical pull" . With them flipped , a horizontal pull almost works but there is not enough lever action to activate the slave carb. I rivetted an "L" shaped piece to the throttle linkage. Now the horizontal pull of the HUSSKI system will activate both carbs. The pivoting attachment was robbed off a ramdom carb.
- Attachments
-
- extralever.jpg (137.91KiB)Viewed 7993 times
- Barrie2777
- Posts:1547
- Joined:Tue Mar 04, 2008 9:17 pm
- Location:Arundel Quebec
Re: model 600 restoration
Just the choke lever to deal with....this one was meant to be adjusted manually....no cable. I removed the choke plate then slid out the choke rod...careful to not loose the ball and spring which keep it open. This part was slid on then reassemled the choke rod and plate.
- Attachments
-
- rod attachment.jpg (175.63KiB)Viewed 7993 times
- Barrie2777
- Posts:1547
- Joined:Tue Mar 04, 2008 9:17 pm
- Location:Arundel Quebec
- Barrie2777
- Posts:1547
- Joined:Tue Mar 04, 2008 9:17 pm
- Location:Arundel Quebec
Re: model 600 restoration
The muffler for the 600 is not fastened to the motor compartement. It is only securred to the motor.
- Attachments
-
- 600mufflerinstalled.jpg (138.47KiB)Viewed 7972 times
-
- 600muffler.jpg (149.06KiB)Viewed 7972 times
Re: model 600 restoration
Nice work, if I could figure out how to upload my pictures of my restoration I will. Barrie, do you have a list of materials and prints for your all purpose sled you built, I would like to build one
- Barrie2777
- Posts:1547
- Joined:Tue Mar 04, 2008 9:17 pm
- Location:Arundel Quebec
Re: model 600 restoration
I dont understand your question. Do you want a list of available parts?
- Barrie2777
- Posts:1547
- Joined:Tue Mar 04, 2008 9:17 pm
- Location:Arundel Quebec
Re: model 600 restoration
Now was the time to see if it would run. It had great spark but i wanted to check the timing so i pulled the flywheel and disconnected the points to use the audible tester for when the points open. All was good so i put it all back together but this time no spark!! After concidering all possibilities i took it apart again, checked, back together...still no spark. All apart again but this time I checked the points connection only to find the outside insulating washer was missing. AHHHH! It had fallen off during the audible test. Back together and this engine runs.
- Attachments
-
- plasticpointswasher.jpg (168.8KiB)Viewed 7947 times
- Barrie2777
- Posts:1547
- Joined:Tue Mar 04, 2008 9:17 pm
- Location:Arundel Quebec
Re: model 600 restoration
What is wrong with this carb? Look closely.....
- Attachments
-
- double carb.jpg (231.07KiB)Viewed 7579 times
- myoldhus-ski
- Posts:82
- Joined:Thu Jan 21, 2010 10:01 pm
- Location:Poplar Point Manitoba
Re: model 600 restoration
The aluminum seems worn on the right side. I also do not see and diaphragm parts. Jim
- Barrie2777
- Posts:1547
- Joined:Tue Mar 04, 2008 9:17 pm
- Location:Arundel Quebec
Re: model 600 restoration
This is the slave carb for my 600 with dual carbs. Im still trying to figure out why its doesnt function properly. I dismantled again and this time niticed no welsh plug where there usually is but.....since the slave carb has no low speed jet maybe there is no need for a welsh plug???